how to do binding on table runner?

To do binding on a table runner, you will need to follow these steps:

1. Measure and cut your binding fabric: Determine the length and width of your table runner and add the measurements of all four sides. Add a few extra inches for seam allowance and overlap. Cut strips of fabric that are 2.5 inches wide and the total length needed.

2. Join the binding strips: If your table runner is longer than the length of your fabric, you will need to join multiple strips together. To do this, place two strips at a right angle with right sides facing each other. Sew a diagonal line from one corner to the other. Trim the excess fabric and press the seam open.

3. Prepare the binding: Fold the binding strip in half lengthwise with wrong sides together and press. This will create a crease down the center.

4. Attach the binding: Starting in the middle of one side of the table runner, align the raw edges of the binding strip with the raw edge of the runner. Pin or clip in place. Sew the binding to the runner using a ¼ inch seam allowance, stopping ¼ inch away from the corner.

5. Miter the corners: Fold the binding strip up, away from the table runner, creating a 45-degree angle at the corner. Then fold it back down, aligning the raw edges with the next side of the runner. Continue sewing, repeating this process for all corners.

6. Finish the binding: When you reach the starting point, overlap the binding strip by a few inches. Trim any excess fabric. Fold the end of the binding strip under and tuck it into the starting point. Sew across the overlap to secure it.

7. Press and finish: Press the binding away from the table runner, both on the front and back. Fold the binding over to the back of the runner and hand stitch it in place using a blind stitch or slip stitch.

By following these steps, you will be able to successfully bind a table runner.

1、 Choosing the right fabric for table runner binding

To do binding on a table runner, you will need the following materials: fabric for the binding, a ruler, a rotary cutter or scissors, pins, an iron, and a sewing machine.

1. Measure the sides of your table runner to determine the length of binding needed. Add a few extra inches to ensure you have enough.

2. Cut strips of fabric for the binding. The width of the strips should be double the desired finished width of the binding, plus an additional ¼ inch for seam allowance. For example, if you want a ½ inch finished binding, cut strips that are 1 ¼ inches wide.

3. Sew the strips together at a 45-degree angle to create one continuous strip. Trim the excess fabric and press the seams open.

4. Fold the binding strip in half lengthwise, wrong sides together, and press with an iron.

5. Starting in the middle of one side of the table runner, align the raw edges of the binding strip with the raw edge of the runner. Pin in place.

6. Sew the binding to the runner using a ¼ inch seam allowance. Stop sewing about ¼ inch from the corner, backstitch, and remove the runner from the machine.

7. Fold the binding strip up at a 45-degree angle, creating a mitered corner. Then fold it back down, aligning the raw edges with the next side of the runner. Pin in place.

8. Continue sewing the binding to the runner, repeating the mitered corner process at each corner.

9. When you reach the starting point, overlap the binding strip and trim off any excess. Fold the end under and sew it down to create a clean finish.

Choosing the right fabric for table runner binding is important to ensure durability and aesthetic appeal. Consider the overall design and color scheme of your table runner when selecting the binding fabric. It should complement or contrast with the main fabric in a pleasing way. Additionally, choose a fabric that is sturdy and can withstand regular use and washing. Cotton or linen fabrics are popular choices for table runner bindings due to their durability and versatility. However, you can also experiment with other fabrics such as silk or velvet for a more luxurious look. Ultimately, the choice of fabric for the binding depends on your personal preference and the desired style of your table runner.

2、 Measuring and cutting the binding strips accurately

To accurately measure and cut binding strips for a table runner, follow these steps:

1. Determine the desired width of the binding. The standard width is usually 2.5 inches, but you can adjust it according to your preference.

2. Measure the perimeter of the table runner. Add the length of all four sides together to get the total length.

3. Calculate the number of binding strips needed. Divide the total length by the width of the binding strip. Round up to the nearest whole number to ensure you have enough strips.

4. Cut the fabric into strips. Use a rotary cutter, ruler, and cutting mat for precise measurements. Align the ruler with the fabric edge and cut along the ruler's edge to create straight strips.

5. Join the strips together. Lay two strips right sides together at a 90-degree angle, forming an L shape. Sew a diagonal line from one corner to the other. Trim the excess fabric and press the seam open. Repeat this process until all the strips are joined.

6. Press the binding strips. Fold the strip in half lengthwise, wrong sides together, and press with an iron. This will create a crease down the center.

7. Attach the binding to the table runner. Starting in the middle of one side, align the raw edges of the binding strip with the raw edge of the table runner. Sew with a ¼ inch seam allowance, stopping ¼ inch away from the corner. Pivot the fabric and continue sewing along the next side. Repeat this process for all four sides, mitering the corners as you go.

8. Fold the binding over to the backside of the table runner and hand stitch it in place using a blind stitch or a decorative stitch.

Remember to adjust these steps based on the latest techniques and trends in binding.

3、 Mitering the corners for a professional finish

To achieve a professional finish when binding a table runner, mitering the corners is a crucial step. Mitering the corners creates a neat and clean look by eliminating bulky and overlapping fabric. Here's a step-by-step guide on how to miter the corners for a professional finish:

1. Start by folding and pressing the binding in half lengthwise, wrong sides together.

2. Begin sewing the binding to the table runner, leaving a tail of about 6 inches unsewn. Align the raw edges of the binding with the raw edges of the runner, starting in the middle of one side.

3. Sew the binding in place, using a ¼ inch seam allowance. Stop sewing approximately ¼ inch away from the first corner.

4. Fold the binding up, away from the table runner, creating a 45-degree angle at the corner. Then, fold the binding back down, aligning the raw edges with the next side of the runner.

5. Continue sewing along the next side, starting at the folded edge of the binding. Repeat steps 3 and 4 for each corner.

6. When you reach the starting point, stop sewing a few inches before the tail of the binding.

7. Trim the excess binding, leaving a 6-inch tail. Open up the binding and fold the tail in half lengthwise, wrong sides together. Press it flat.

8. Insert the tail into the starting point, tucking it under the folded edge of the binding.

9. Finish sewing the binding in place, overlapping the stitches slightly.

By mitering the corners, you'll achieve a professional and polished look for your table runner. Remember to press the binding after sewing to ensure a crisp finish.

4、 Hand-stitching or machine-stitching the binding in place

To do binding on a table runner, you have two options: hand-stitching or machine-stitching the binding in place. Both methods have their advantages and it ultimately depends on your personal preference and the desired outcome.

Hand-stitching the binding is a traditional and time-honored method. It allows for more control and precision, resulting in a neater and more professional finish. To hand-stitch the binding, you will need a needle, thread, and some basic sewing skills. Start by folding the binding in half lengthwise and pressing it to create a crease. Then, align the raw edges of the binding with the raw edges of the table runner and pin them in place. Using a slip stitch or a blind stitch, sew the binding to the runner, making sure to catch both layers of fabric.

On the other hand, machine-stitching the binding is a quicker and more efficient method. It is ideal for those who are short on time or prefer a more modern look. To machine-stitch the binding, you will need a sewing machine with a straight stitch or a decorative stitch. Start by attaching the binding to the front of the table runner, aligning the raw edges and pinning them in place. Then, sew along the edge of the binding, making sure to catch both layers of fabric. Finally, fold the binding over to the back of the runner and secure it with pins. Stitch in the ditch or use a decorative stitch to sew the binding in place from the front.

In recent years, there has been a growing trend of using a combination of hand-stitching and machine-stitching for binding. This technique involves machine-stitching the binding to the front of the runner and then hand-stitching it to the back. This method combines the speed and efficiency of machine-stitching with the precision and neatness of hand-stitching, resulting in a beautiful and durable finish.

In conclusion, whether you choose to hand-stitch or machine-stitch the binding on your table runner, both methods can yield excellent results. Consider your personal preferences, time constraints, and desired outcome to determine which method is best for you.